Sign in

to your account

Your shopping cart

Shopping cart is empty.
Cart

Mitas 120/90-18 XT 754 SUPER LIGHT

Manufacturer: MITAS SKU: MITAS*120/90*18 XT754S

Designed for extrem country cross.Works great on hard rocky terrain. High profile studs that dig deep.Exceptional traction on any loose terrain.Semi-s Show all

96.67 €

Not in stock

Designed for extrem country cross.

Works great on hard rocky terrain. High profile studs that dig deep.
Exceptional traction on any loose terrain.
Semi-soft but long-lasting compound.

Technical description
Manufacturer Mitas
Description + profile Mitas 120 / 90-18 66M XT-754 Super-Lightgr
Rear position
Load / speed 66 / M

Off-road season
Name Super-Light green
Info NHS, green markings, green stripe
Measuring rim 2.75x18
Allowable rim width 2.50-3.00x18
Tyre markings for motocross and enduro:
Red stripe - tyre marking for motocross
Yellow stripe - tyres with softer compounds suitable for FIM enduro and cross country competitions
Green stripe - tyres with softer carcass and soft tread for hard enduro competitions
Double green stripe - tyres with softer carcass and very soft tread compound for extreme hard enduro competitions
White stripe - tyres for winter use, motoskyöring and motocross on ice
No stripe tyres - classic motocross tyres

Use and maintenance:
Store tyres clean and away from sources of heat, light, ozone or hydrocarbons. Avoid prolonged exposure of tyres to direct sunlight. Avoid any contact with grease, petrol, volatile solvents or other agents that may damage the rubber. Avoid horizontal storage of tubeless tyres, only small tyres can be stored horizontally (maximum 6 months). If tyres are stored horizontally, they must be placed tooth to tooth. If tyres are stored mounted on the rim, lower the inflation pressure. Make sure there is no water or moisture inside the tyre. Never store tyres directly in contact with the ground for long periods of time. For safety reasons, tyres should only be repaired by experts using the correct methods and tools. When loading a tyre, the relationship between speed, inflation pressure and load capacity must be taken into account. Overloading causes premature destruction of the tyre. Use technical documentation and inflation tables that define the load and inflation for different operating speeds. Under-inflation is not only caused by improper run-flatting, but also by liner separation or other damage to the tyre liners. Overinflation increases the hardness of the tyre and reduces the resistance to impacts leading to damage to the tyre liners.

Mounting and dismounting instructions
Mounting and dismounting tyres can be dangerous and should only be carried out by trained and qualified personnel using the correct tools and working procedures. Failure to follow these procedures may result in incorrect fitting of the tire to the rim, resulting in destruction of the tire with explosive force that can cause serious injury or death. Make sure the rim, tire and tube are compatible. Check that the tyre is suitable for the equipment/machine. Use only rims recommended or approved by the tire manufacturer. Always use only the correct special equipment and tools. The rim must be clean and in perfect condition (not damaged etc.), if necessary clean the rim with sandpaper. Under no circumstances mount tyres on rims with cracks, seriously deformed, bearing welding repair marks, etc. Carefully inspect the inside as well as the outside of the tyre to identify any damage. If the extent of the damage does not allow repair, the tyre should be devalued. If mounting with a tube, always use the correct new tube and liner for the size. For mounting tubeless tires, on tubeless rims, always use a new tubeless valve. Lubricate the rim and tire bead before mounting. Use only a suitable lubricant that will not destroy the tire (never use silicone or gasoline based lubricants). Vertical mounting is recommended. In the case of horizontal mounting, it is essential to check that the bottom bead is seated correctly. Fit the casing on the rim opposite the valve hole (respect the direction of rotation indicated by the arrows). Using the mounting lever, gradually slide the first bead over the rim rim rim rim. Then insert a lightly inflated inner tube, sufficiently treated with a slip joint (if fitted), into the rim. Position the valve and secure it lightly with the retaining ring. Fit the second foot, working in sequence so that you end up at the valve. Remove the valve liner to seat and center the shell properly. Slowly inflate and check for proper seating of the casing foot. Make sure the casing foot has not pinched the soul. Maintain a safe distance during the densification process, always use a safety cage, preferably attached to a wall or safety chain. During pressure readings, make sure that no part of your body is in the possible trajectory of the valve internals or its cap. It is recommended to use a suitable device to limit the inflation pressure. Use a filter and dehumidifier for the compressed air necessary to remove moisture and dust. If the feet are not seated properly, bleed, re-prime and re-inflate. Repeat this operation until the feet are seated correctly. If all previous operations have been performed correctly, replace the valve liner. Inflate the tyre according to the load. Ensure that the valve does not touch the rim, brake drums or other mechanical parts. Disassembly: never attempt to remove the bead of an inflated tyre. Always remove the valve inner liner. Check that the tyre is completely free of air before dismounting. Never use tools that may damage the rim or tire beads.
Call us, we are glad to help...
Jiří Fulín
Jiri Fulin
Bike lover & your support
+420 736 164 904
obchod@mefo.cz
arrow1 arrow1