Polisport Integral Evo handguards

Polisport handguards help protect one of the most vulnerable areas of the handlebars: the brake and clutch levers, the rider’s hands and the motorcycle’s controls. During a crash, when riding through branches or after contact with another rider, an unprotected lever can receive a direct impact. The result may be more than a scratch—the lever can bend, break or make it impossible to continue riding.

This is where handguards provide their main benefit. They create a protective surface in front of the handlebars, helping to deflect branches, stones, mud and other debris before they reach the rider’s hands or the motorcycle’s controls. Whether used for motocross, enduro, forest trails or riding away from paved roads, they add practical protection exactly where it is needed.

A broken clutch or brake lever can end a training session, race or trail ride within seconds. The cost of handguards is considerably lower than replacing damaged controls, losing valuable riding time or having to recover a motorcycle from difficult terrain. Handguards cannot prevent every type of damage, but they can reduce the direct effect of common impacts and obstacles.

Depending on the specific design, handguards may protect the front of the hands and levers with an open construction or provide more extensive coverage with mounting at the handlebar ends. Open designs are usually lightweight, well ventilated and particularly popular for motocross. More enclosed systems provide broader coverage and are well suited to enduro, adventure riding and technical terrain.

Polisport offers several constructions for different riding styles. Some models prioritise maximum airflow, while others provide a larger protective surface or a stronger two-point mounting system. Selected versions also allow the coverage to be adjusted with a removable upper spoiler. Riders can therefore choose a setup that matches their motorcycle, terrain and preferred level of protection.

Protection for the rider’s hands is equally important. Branches, stones and flying debris can strike the fingers and knuckles painfully at higher speeds. Handguards help deflect part of these impacts, allowing the rider to concentrate more effectively on the chosen line and on operating the throttle, clutch and front brake.

In colder or wet conditions, larger models can also reduce some of the direct wind and water reaching the hands. They do not replace warm or waterproof gloves, but they create an additional barrier between the rider and the conditions ahead of the handlebars. More open motocross designs, on the other hand, allow greater airflow.

Polisport handguards also change the appearance of the motorcycle’s front end. Their shaped plastic panels complement the handlebars and can be coordinated with the motorcycle’s other plastics or graphics. The design is not purely decorative, however—the guards must leave sufficient room for the rider’s hands, levers, cables and normal steering movement.

Browse mefoshop.com selection of motorcycle handguards for motocross, enduro, adventure, road and other motorcycles. The complete range of plastics, guards and accessories from the manufacturer is available in the Polisport category.

Key benefits of Polisport handguards:

• help protect the brake and clutch levers from direct impacts,

• reduce contact between the rider’s hands and branches, stones, mud or debris,

• may lower the risk of a ride ending because of damaged controls,

• provide additional protection for the rider’s fingers and knuckles,

• different constructions for motocross, enduro, adventure and other riding styles,

• choice of open and more enclosed designs,

• single-point or two-point mounting depending on the specific model,

• shape designed around motorcycle control and natural hand movement,

• durable plastic construction prepared for off-road conditions,

• complement the appearance of the handlebars and front of the motorcycle,

• adjustable coverage on selected models,

• available in versions for different handlebars and mounting arrangements.

Why handguards make sense:

Levers are among the first components likely to strike the ground when a motorcycle falls. Even dropping a bike at relatively low speed may bend or break them. In the terrain, this risk is joined by branches, stones, narrow passages and debris thrown up by other motorcycles.

Handguards take part of these impacts and create another barrier in front of the rider’s hands and controls. They are not merely a visual accessory, but a functional component that may determine whether the rider continues after a minor fall or has to deal with a broken lever.

Why Polisport:

Polisport specialises in motorcycle plastics and protective components. Its handguard range includes lightweight motocross designs, universal models and more enclosed systems intended for demanding enduro and adventure use.

The manufacturer uses different mounting methods and protective surface sizes, so riders do not have to accept one universal compromise for every situation. They can select a design that matches their riding style, desired airflow and required level of coverage.

How to choose the correct version:

Before ordering, check the type of handlebars, their outside and inside diameter, the available space around the lever clamps and the required mounting method. Some handguards include the complete mounting kit, while others may require suitable brackets or adapters to be purchased separately.

Always follow the information provided with the individual product. Also decide whether you prefer a lightweight open design with greater airflow or more enclosed protection for dense terrain, enduro riding and longer journeys.